Use the ultrasonic cleaner to check the product you are cleaning, and then use what lotion to confirm the ultrasonic frequency you are using. Assume that your ultrasonic cleaner has several tanks, including heating, drying or slow pulling. There are many factors to consider, such as temperature, detergent concentration and cleaning time.

一般機械設備五金件用28KHZ去油蠟，光學鏡片用40K，實驗室科研用100K,LCD半導體材料元件1MHZ及以上。現在一般廠家提供的超聲波清洗機都能夠調理輸出功率，在考慮了整理規則和整理時刻的前提下，能夠挑選適宜的輸出功率。

28KHZ degreasing wax is used for hardware of general mechanical equipment, 40K for optical lens, 100K for laboratory scientific research, and 1MHZ or above for LCD semiconductor material elements. Now the ultrasonic cleaners provided by general manufacturers can adjust the output power, and can select the appropriate output power on the premise of considering the finishing rules and finishing time.

除蠟油一般采用偏堿性的清洗液，溫度控制在75度上下適宜，如規則的工作效率和清洗質量等，有些溶劑能夠提供挑選。超聲波清洗機的超聲頻率越低，對液體形成空蝕越簡單，效果也越好；頻率高且超聲專一性強，合適細微物體的清洗。

Generally, the wax remover uses alkaline cleaning solution, and the temperature should be controlled around 75 ℃, such as regular work efficiency and cleaning quality. Some solvents can be selected. The lower the ultrasonic frequency of the ultrasonic cleaner is, the simpler it is to form cavitation erosion on the liquid, and the better the effect is; High frequency and strong ultrasonic specificity, suitable for cleaning of fine objects.

超聲功率越大，空化效果越強，整理速度越快，實際效果越好。而對于外表較光滑、精度較高的產品，采用長時刻高功率的清洗會對外表物體產生“空蝕”效果。

The higher the ultrasonic power, the stronger the cavitation effect, the faster the finishing speed, and the better the actual effect. For products with smooth appearance and high accuracy, long-term high-power cleaning will produce "cavitation" effect on external surface objects.

挑選超聲清洗，一般有兩種類型的洗滌劑，分別為化學有機溶劑和水基洗滌劑。整理物質的氧化效果，再加上超聲波整理的物理效果，兩者的效果緊密結合，才干充沛、合理地對物體進行整理。一般來說，30℃-40℃的超音波侵蝕實際上效果很好。洗滌劑則是溫度越高，效果越顯著。通常詳細運用超聲波清洗時，運用溫度為40℃-60℃。

There are generally two types of detergents for ultrasonic cleaning, namely chemical organic solvent and water-based detergent. The oxidation effect of the finishing materials, coupled with the physical effect of ultrasonic finishing, are closely combined to finish the objects reasonably and efficiently. Generally speaking, ultrasonic erosion at 30 ℃ - 40 ℃ is actually very effective. The higher the temperature is, the more effective the detergent is. Generally, when ultrasonic cleaning is applied in detail, the application temperature is 40 ℃ - 60 ℃.

柴油發電機組一般運行500h后應更換機油一次，但有時候未到更換期，或還沒用多長時間出現機油變稀、雜質增多現象，無法繼續使用。     柴油發電機組機油為何會變質過快     ①、機油牌號不對、質量達不到要求，一般增壓和標定轉速大于2000r/min的柴油發電機應選用CC級以上的機油；     ②、柴油機發電機技術狀況不好，竄氣、竄油、配合間隙過大或油溫過高；     ③、柴油機發電機經常在低溫、低負荷、低速下運轉，活塞變形量不夠，燃燒不完全，有柴油沿缸 壁進入油底殼使機油稀釋變質；     ④、廢氣進入油底殼凝結成水分和酸性物質，使機油變質；     ⑤、機油濾芯臟，未經濾清的臟機油進入潤滑部位，加速了零件的磨損。     ⑥、濾芯密封圈破裂而發生內漏，一部分機油未經濾芯而直接通過濾清器而造成機油變質。

Generally, the engine oil of the diesel generator set should be replaced once after 500h of operation, but sometimes the replacement period is not reached, or the engine oil has become thinner and impurities have increased within a short period of time, which makes it impossible to continue to use. Why the engine oil of the diesel generator set deteriorates too fast ①. The engine oil is of the wrong brand and the quality does not meet the requirements. Generally, the diesel generator with supercharging and rated speed greater than 2000r/min should use the engine oil above CC level; ② The diesel generator is in poor technical condition, with gas and oil leakage, too large fitting clearance or too high oil temperature; ③ The diesel engine generator often operates at low temperature, low load and low speed. The piston deformation is not enough and the combustion is incomplete. Diesel enters the oil pan along the cylinder wall to dilute and deteriorate the oil; ④ Waste gas enters the oil pan and condenses into water and acid substances, which will deteriorate the engine oil; ⑤ The oil filter element is dirty, and the unfiltered dirty oil enters the lubricating part, which accelerates the wear of parts. ⑥ . The sealing ring of the filter element is broken and internal leakage occurs. Some engine oil directly passes through the filter element without passing through the filter element, causing deterioration of the engine oil.

以上是為大家介紹的有關 超聲波清洗機的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://m.ishihara2010.com

The above is a detailed introduction about the price of ultrasonic cleaning machine. I hope it will be helpful to you. If you have any questions, please contact us. We will provide you with professional services http://m.ishihara2010.com